LINAC2022 - List of Keywords (acceleration)

Paper	Title	Other Keywords	Page
MOPOGE23	Conservation of Quality Factor for Superconducting Cavity and Heartbeat under Relativistic Motion	cavity, superconducting-cavity, resonance, ECR	204
	H. Kim IBS, Daejeon, Republic of Korea
	Funding: This research was supported by the Rare Isotope Science Project of Institute for Basic Science funded by Ministry of Science and National Research Foundation of Korea (NRF-2013M7A1A1075764). The conservation of quality factor under relativistic motion is applied to the superconducting cavity as well as the heartbeat of mammal. The quality factor of the superconducting cavity is conserved under relativistic motion. The frequency of the cavity decreases and the decay time increases as the velocity and acceleration are increased. The quality factor of the superconducting cavity is comparable with the total heartbeat of the mammal. The quality factor for the heartbeat of the mammal representing the total number of heartbeat is also conserved under relativistic motion. Therefore, the heart rate is inversely proportional to the life expectancy under relativistic motion.
	Poster MOPOGE23 [0.765 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2022-MOPOGE23
About •	Received ※ 25 July 2022 — Revised ※ 23 August 2022 — Accepted ※ 30 August 2022 — Issue date ※ 02 September 2022
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPOPA24	Design of an X-Band Bunching and Accelerating System for AWAKE Run 2	cavity, electron, bunching, gun	458
	J.M. Arnesano, S. Döbert CERN, Meyrin, Switzerland
	The AWAKE experiment at CERN demonstrated in its Run 1 that it is possible to accelerate electrons in plasma wakefields driven by a self-modulated proton bunch. In Run2, AWAKE aims to increase the accelerating gradient in the plasma even further and demonstrate beam quality in order to be ready for high-energy physics experiments. In this framework, a new electron injector, consisting of an S-band RF-gun and a subsequent X-band bunching and accelerating section, capable of producing very short bunches with a small emittance, has been designed. In this paper, two different configurations of the X-band section and their corresponding high-power distribution systems are presented. The first one consists of three identical cavities to bunch and accelerate the beam while the second one uses a separate short structure for velocity bunching followed by three long, pure accelerating structures. A discussion of the strengths and weaknesses of each configuration is carried out and beam dynamics aspects are analyzed. Finally the X-Band power distribution systems are described with particular attention to the choice of the klystron, the pulse compression system and the waveguide distribution.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2022-TUPOPA24
About •	Received ※ 12 August 2022 — Revised ※ 21 August 2022 — Accepted ※ 01 September 2022 — Issue date ※ 16 September 2022
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPOGE08	Design of a Transport System for the PIP-II HB650 Cryomodule	ISOL, cryomodule, simulation, operation	498
	M.T.W. Kane STFC/DL/ASTeC, Daresbury, Warrington, Cheshire, United Kingdom J.P. Holzbauer Fermilab, Batavia, Illinois, USA T.J. Jones, E.S. Jordan STFC/DL, Daresbury, Warrington, Cheshire, United Kingdom
	The PIP-II Project at FNAL requires the assembly of 3 high-beta 650MHz cryomodules at STFC Daresbury (DL) in the UK. These modules must be safely transported from DL to FNAL in the USA. Previous experience with cryomodule transport was leveraged at both labs to design a transport system to protect the cryomodules during transit. Requirements for the system included mitigation of shocks, drops, and vibrations, and acting as a lifting fixture. It is comprised of a tessellated steel frame which encompasses the module with a wire rope isolator arrangement which the module mounts to. The frame was designed to withstand the weight of the 12.5 tonne cryomodule in various load cases. Details of shock and vibration profiles were obtained from MIL-STD-810H and were used to guide the sizing of the isolators. The frame and the isolation system were analysed via FEA using the shock and vibration profiles as an input. The transport system was found to be suitable for the given isolation, frame stiffness, and lifting code requirements. The frame has been fabricated and successfully load tested at FNAL. It will now be road tested with a dummy cryomodule before undergoing a trial run to DL.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2022-TUPOGE08
About •	Received ※ 24 August 2022 — Revised ※ 29 August 2022 — Accepted ※ 31 August 2022 — Issue date ※ 02 September 2022
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPORI08	End-to-End Simulations and Error Studies of the J-PARC Muon Linac	linac, experiment, emittance, simulation	562
	Y. Takeuchi, J. Tojo, T. Yamanaka Kyushu University, Fukuoka, Japan E. Cicek, H. Ego, K. Futatsukawa, N. Kawamura, T. Mibe, M. Otani, N. Saito, T. Yamazaki KEK, Ibaraki, Japan H. Iinuma, Y. Nakazawa Ibaraki University, Ibaraki, Japan Y. Iwashita Kyoto University, Research Reactor Institute, Osaka, Japan R. Kitamura, Y. Kondo, T. Morishita JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken, Japan Y. Sato Niigata University, Niigata, Japan Y. Sue, K. Sumi, M. Yotsuzuka Nagoya University, Graduate School of Science, Chikusa-ku, Nagoya, Japan H.Y. Yasuda University of Tokyo, Tokyo, Japan
	A muon linac is under development for future muon ’’’ 2/EDM experiments at J-PARC. The linac provides a 212 MeV muon beam to an MRI-type compact storage ring. Af- ter the initial acceleration using the electrostatic field created by mesh and cylindrical electrodes, the muons are acceler- ated using four types of radio-frequency accelerators. To validate the linac design as a whole, end-to-end simulations were performed using General Particle Tracer. In addition, error studies is ongoing to investigate the effects on beam and spin dynamics of various errors in the accelerator com- ponents and input beam distribution. This paper describes the preliminary results of the end-to-end simulations and error studies.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2022-TUPORI08
About •	Received ※ 24 August 2022 — Revised ※ 25 August 2022 — Accepted ※ 31 August 2022 — Issue date ※ 12 October 2022
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPORI19	Beam Dynamics Framework Incorporating Acceleration Used to Define the Minimum Aperture of RF Cavity For FODO-like Focusing Scheme for Proton Radiotherapy Linac	cavity, quadrupole, focusing, lattice	589
	M.J.W. Southerby, R. Apsimon Cockcroft Institute, Lancaster University, Lancaster, United Kingdom
	Funding: Supported by the Cockcroft Institute Core Grant, ST/P002056/1. In this paper, we present a generalised analytical framework for beam dynamics studies and lattice designs, while incorporating longitudinal acceleration of bunches of charged particles. We study a ’FODO-like’ scheme, whereby we have an alternating array of focusing and defocusing quadrupoles and study how this differs from a standard FODO lattice due to acceleration. We present optimisation techniques to provide quadrupole parameters, cavity lengths, and required drift lengths under different constraints.
	Poster TUPORI19 [0.997 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2022-TUPORI19
About •	Received ※ 23 August 2022 — Revised ※ 27 August 2022 — Accepted ※ 29 August 2022 — Issue date ※ 01 September 2022
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPORI26	Longitudinal Beam Dynamics in Array of Equidistant Multicell Cavities	cavity, linac, emittance, space-charge	609
	Y.K. Batygin LANL, Los Alamos, New Mexico, USA
	Funding: Work supported by US DOE under contract 89233218CNA000001 Linear accelerators containing the sequence of independently phase cavities with constant geometrical velocity along each cavity are widely used in practice. The chain of cavities with identical cell length is utilized within a certain beam velocity range, with subsequent transformation to the next chain with higher cavity velocity. Design and analysis of beam dynamics in this type of accelerators are usually performed using numerical simulations. In the present paper, we provide an analytical treatment of beam dynamics in such linacs. Expressions connecting beam energy gain and phase slippage along the cavity are implemented. The dynamics of the beam around the reference trajectory along the accelerator and matched beam conditions are discussed.
	Poster TUPORI26 [1.718 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2022-TUPORI26
About •	Received ※ 20 August 2022 — Revised ※ 28 August 2022 — Accepted ※ 01 September 2022 — Issue date ※ 02 September 2022
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WE1AA05	The Muon Linac Project at J-PARC	linac, rfq, DTL, experiment	636
	Y. Kondo, Y. Fuwa, R. Kitamura, K. Moriya, T. Takayanagi JAEA/J-PARC, Tokai-mura, Japan S. Bae, H. Choi, S. Choi, B. Kim, H.S. Ko SNU, Seoul, Republic of Korea E. Cicek, H. Ego, Y. Fukao, K. Futatsukawa, N. Kawamura, T. Mibe, Y. Miyake, S. Mizobata, M. Otani, N. Saito, K. Shimomura, T. Yamazaki, M. Yoshida KEK, Ibaraki, Japan K. Hasegawa QST Rokkasho, Aomori, Japan N. Hayashizaki Research Laboratory for Nuclear Research, Tokyo Institute of Technology, Tokyo, Japan T. Iijima, Y. Sue, K. Sumi Nagoya University, Graduate School of Science, Chikusa-ku, Nagoya, Japan H. Iinuma, Y. Nakazawa Ibaraki University, Ibaraki, Japan K. Inami, K. Suzuki, M. Yotsuzuka Nagoya University, Nagoya, Japan K. Ishida RIKEN Nishina Center, Wako, Japan Y. Iwashita Kyoto ICR, Uji, Kyoto, Japan T. Morishita JAEA/LINAC, Ibaraki-ken, Japan G.P. Razuvaev Budker INP & NSU, Novosibirsk, Russia Y. Takeuchi, J. Tojo Kyushu University, Fukuoka, Japan E. Won Korea University, Seoul, Republic of Korea H.Y. Yasuda University of Tokyo, Tokyo, Japan
	The muon linac project for the precise measurement of the muon anomalous magnetic and electric dipole moments, which is currently one of the hottest issues of the elementary particle physics, is in progress at J-PARC. The muons from the J-PARC muon facility are once cooled to room temperature, then accelerated up to 212 MeV with a normalized emittance of 1.5 pi mm mrad and a momentum spread of 0.1%. Four types of accelerating structures are adopted to obtain the efficient acceleration with a wide beta range from 0.01 to 0.94. The project is moving into the construction phase. They already demonstrated the re-acceleration scheme of the decelerated muons using a 324-MHz RFQ in 2017. The high-power test of the 324-MHz Interdigital H-mode (IH) DTL using a prototype cavity will be performed in 2021. The fabrication of the first module of 14 modules of the 1296-MHz Disk and Washer (DAW) CCL will be done to confirm the production process. Moreover, the final design of the travelling wave accelerating structure for the high beta region is also proceeding. In this presentation, the recent progress toward the realization of the world first muon linac will be presented.

	please see instructions how to view/control embeded videos
	Slides WE1AA05 [3.764 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2022-WE1AA05
About •	Received ※ 14 August 2022 — Revised ※ 21 August 2022 — Accepted ※ 01 September 2022 — Issue date ※ 16 September 2022
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPOJO01	The ARES Linac at DESY	experiment, electron, linac, diagnostics	691
	F. Burkart, R.W. Aßmann, H. Dinter, S. Jaster-Merz, W. Kuropka, F. Mayet, T. Vinatier DESY, Hamburg, Germany
	The generation and acceleration of ultra-short, high quality electron beams has attracted more and more interest in accelerator science. Electron bunches with these properties are necessary to operate and test novel diagnostics and advanced high gradient accelerating schemes. Furthermore, several medical and industrial applications require high-brightness electron beams. The dedicated R&D linac ARES at DESY (Deutsches Elektronen-Synchrotron) is now fully operational and able to produce these electron beams at the nominal energy of 155 MeV and deliver it to users. This paper gives an overview of the ARES linac and summarizes the beam parameter measurements. The possibilities for user operation will be described in detail.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2022-THPOJO01
About •	Received ※ 23 August 2022 — Revised ※ 31 August 2022 — Accepted ※ 01 September 2022 — Issue date ※ 06 September 2022
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Other Keywords

Page

MOPOGE23

Conservation of Quality Factor for Superconducting Cavity and Heartbeat under Relativistic Motion

cavity, superconducting-cavity, resonance, ECR

204

H. Kim
IBS, Daejeon, Republic of Korea

Funding: This research was supported by the Rare Isotope Science Project of Institute for Basic Science funded by Ministry of Science and National Research Foundation of Korea (NRF-2013M7A1A1075764).
The conservation of quality factor under relativistic motion is applied to the superconducting cavity as well as the heartbeat of mammal. The quality factor of the superconducting cavity is conserved under relativistic motion. The frequency of the cavity decreases and the decay time increases as the velocity and acceleration are increased. The quality factor of the superconducting cavity is comparable with the total heartbeat of the mammal. The quality factor for the heartbeat of the mammal representing the total number of heartbeat is also conserved under relativistic motion. Therefore, the heart rate is inversely proportional to the life expectancy under relativistic motion.

Poster MOPOGE23 [0.765 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2022-MOPOGE23

About •

Received ※ 25 July 2022 — Revised ※ 23 August 2022 — Accepted ※ 30 August 2022 — Issue date ※ 02 September 2022

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPOPA24

Design of an X-Band Bunching and Accelerating System for AWAKE Run 2

cavity, electron, bunching, gun

458

J.M. Arnesano, S. Döbert
CERN, Meyrin, Switzerland

The AWAKE experiment at CERN demonstrated in its Run 1 that it is possible to accelerate electrons in plasma wakefields driven by a self-modulated proton bunch. In Run2, AWAKE aims to increase the accelerating gradient in the plasma even further and demonstrate beam quality in order to be ready for high-energy physics experiments. In this framework, a new electron injector, consisting of an S-band RF-gun and a subsequent X-band bunching and accelerating section, capable of producing very short bunches with a small emittance, has been designed. In this paper, two different configurations of the X-band section and their corresponding high-power distribution systems are presented. The first one consists of three identical cavities to bunch and accelerate the beam while the second one uses a separate short structure for velocity bunching followed by three long, pure accelerating structures. A discussion of the strengths and weaknesses of each configuration is carried out and beam dynamics aspects are analyzed. Finally the X-Band power distribution systems are described with particular attention to the choice of the klystron, the pulse compression system and the waveguide distribution.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2022-TUPOPA24

About •

Received ※ 12 August 2022 — Revised ※ 21 August 2022 — Accepted ※ 01 September 2022 — Issue date ※ 16 September 2022

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPOGE08

Design of a Transport System for the PIP-II HB650 Cryomodule

ISOL, cryomodule, simulation, operation

498

M.T.W. Kane
STFC/DL/ASTeC, Daresbury, Warrington, Cheshire, United Kingdom
J.P. Holzbauer
Fermilab, Batavia, Illinois, USA
T.J. Jones, E.S. Jordan
STFC/DL, Daresbury, Warrington, Cheshire, United Kingdom

The PIP-II Project at FNAL requires the assembly of 3 high-beta 650MHz cryomodules at STFC Daresbury (DL) in the UK. These modules must be safely transported from DL to FNAL in the USA. Previous experience with cryomodule transport was leveraged at both labs to design a transport system to protect the cryomodules during transit. Requirements for the system included mitigation of shocks, drops, and vibrations, and acting as a lifting fixture. It is comprised of a tessellated steel frame which encompasses the module with a wire rope isolator arrangement which the module mounts to. The frame was designed to withstand the weight of the 12.5 tonne cryomodule in various load cases. Details of shock and vibration profiles were obtained from MIL-STD-810H and were used to guide the sizing of the isolators. The frame and the isolation system were analysed via FEA using the shock and vibration profiles as an input. The transport system was found to be suitable for the given isolation, frame stiffness, and lifting code requirements. The frame has been fabricated and successfully load tested at FNAL. It will now be road tested with a dummy cryomodule before undergoing a trial run to DL.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2022-TUPOGE08

About •

Received ※ 24 August 2022 — Revised ※ 29 August 2022 — Accepted ※ 31 August 2022 — Issue date ※ 02 September 2022

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPORI08

End-to-End Simulations and Error Studies of the J-PARC Muon Linac

linac, experiment, emittance, simulation

562

Y. Takeuchi, J. Tojo, T. Yamanaka
Kyushu University, Fukuoka, Japan
E. Cicek, H. Ego, K. Futatsukawa, N. Kawamura, T. Mibe, M. Otani, N. Saito, T. Yamazaki
KEK, Ibaraki, Japan
H. Iinuma, Y. Nakazawa
Ibaraki University, Ibaraki, Japan
Y. Iwashita
Kyoto University, Research Reactor Institute, Osaka, Japan
R. Kitamura, Y. Kondo, T. Morishita
JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken, Japan
Y. Sato
Niigata University, Niigata, Japan
Y. Sue, K. Sumi, M. Yotsuzuka
Nagoya University, Graduate School of Science, Chikusa-ku, Nagoya, Japan
H.Y. Yasuda
University of Tokyo, Tokyo, Japan

A muon linac is under development for future muon ’’’ 2/EDM experiments at J-PARC. The linac provides a 212 MeV muon beam to an MRI-type compact storage ring. Af- ter the initial acceleration using the electrostatic field created by mesh and cylindrical electrodes, the muons are acceler- ated using four types of radio-frequency accelerators. To validate the linac design as a whole, end-to-end simulations were performed using General Particle Tracer. In addition, error studies is ongoing to investigate the effects on beam and spin dynamics of various errors in the accelerator com- ponents and input beam distribution. This paper describes the preliminary results of the end-to-end simulations and error studies.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2022-TUPORI08

About •

Received ※ 24 August 2022 — Revised ※ 25 August 2022 — Accepted ※ 31 August 2022 — Issue date ※ 12 October 2022

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPORI19

Beam Dynamics Framework Incorporating Acceleration Used to Define the Minimum Aperture of RF Cavity For FODO-like Focusing Scheme for Proton Radiotherapy Linac

cavity, quadrupole, focusing, lattice

589

M.J.W. Southerby, R. Apsimon
Cockcroft Institute, Lancaster University, Lancaster, United Kingdom

Funding: Supported by the Cockcroft Institute Core Grant, ST/P002056/1.
In this paper, we present a generalised analytical framework for beam dynamics studies and lattice designs, while incorporating longitudinal acceleration of bunches of charged particles. We study a ’FODO-like’ scheme, whereby we have an alternating array of focusing and defocusing quadrupoles and study how this differs from a standard FODO lattice due to acceleration. We present optimisation techniques to provide quadrupole parameters, cavity lengths, and required drift lengths under different constraints.

Poster TUPORI19 [0.997 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2022-TUPORI19

About •

Received ※ 23 August 2022 — Revised ※ 27 August 2022 — Accepted ※ 29 August 2022 — Issue date ※ 01 September 2022

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPORI26

Longitudinal Beam Dynamics in Array of Equidistant Multicell Cavities

cavity, linac, emittance, space-charge

609

Y.K. Batygin
LANL, Los Alamos, New Mexico, USA

Funding: Work supported by US DOE under contract 89233218CNA000001
Linear accelerators containing the sequence of independently phase cavities with constant geometrical velocity along each cavity are widely used in practice. The chain of cavities with identical cell length is utilized within a certain beam velocity range, with subsequent transformation to the next chain with higher cavity velocity. Design and analysis of beam dynamics in this type of accelerators are usually performed using numerical simulations. In the present paper, we provide an analytical treatment of beam dynamics in such linacs. Expressions connecting beam energy gain and phase slippage along the cavity are implemented. The dynamics of the beam around the reference trajectory along the accelerator and matched beam conditions are discussed.

Poster TUPORI26 [1.718 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2022-TUPORI26

About •

Received ※ 20 August 2022 — Revised ※ 28 August 2022 — Accepted ※ 01 September 2022 — Issue date ※ 02 September 2022

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WE1AA05

The Muon Linac Project at J-PARC

linac, rfq, DTL, experiment

636

Y. Kondo, Y. Fuwa, R. Kitamura, K. Moriya, T. Takayanagi
JAEA/J-PARC, Tokai-mura, Japan
S. Bae, H. Choi, S. Choi, B. Kim, H.S. Ko
SNU, Seoul, Republic of Korea
E. Cicek, H. Ego, Y. Fukao, K. Futatsukawa, N. Kawamura, T. Mibe, Y. Miyake, S. Mizobata, M. Otani, N. Saito, K. Shimomura, T. Yamazaki, M. Yoshida
KEK, Ibaraki, Japan
K. Hasegawa
QST Rokkasho, Aomori, Japan
N. Hayashizaki
Research Laboratory for Nuclear Research, Tokyo Institute of Technology, Tokyo, Japan
T. Iijima, Y. Sue, K. Sumi
Nagoya University, Graduate School of Science, Chikusa-ku, Nagoya, Japan
H. Iinuma, Y. Nakazawa
Ibaraki University, Ibaraki, Japan
K. Inami, K. Suzuki, M. Yotsuzuka
Nagoya University, Nagoya, Japan
K. Ishida
RIKEN Nishina Center, Wako, Japan
Y. Iwashita
Kyoto ICR, Uji, Kyoto, Japan
T. Morishita
JAEA/LINAC, Ibaraki-ken, Japan
G.P. Razuvaev
Budker INP & NSU, Novosibirsk, Russia
Y. Takeuchi, J. Tojo
Kyushu University, Fukuoka, Japan
E. Won
Korea University, Seoul, Republic of Korea
H.Y. Yasuda
University of Tokyo, Tokyo, Japan

The muon linac project for the precise measurement of the muon anomalous magnetic and electric dipole moments, which is currently one of the hottest issues of the elementary particle physics, is in progress at J-PARC. The muons from the J-PARC muon facility are once cooled to room temperature, then accelerated up to 212 MeV with a normalized emittance of 1.5 pi mm mrad and a momentum spread of 0.1%. Four types of accelerating structures are adopted to obtain the efficient acceleration with a wide beta range from 0.01 to 0.94. The project is moving into the construction phase. They already demonstrated the re-acceleration scheme of the decelerated muons using a 324-MHz RFQ in 2017. The high-power test of the 324-MHz Interdigital H-mode (IH) DTL using a prototype cavity will be performed in 2021. The fabrication of the first module of 14 modules of the 1296-MHz Disk and Washer (DAW) CCL will be done to confirm the production process. Moreover, the final design of the travelling wave accelerating structure for the high beta region is also proceeding. In this presentation, the recent progress toward the realization of the world first muon linac will be presented.

please see instructions how to view/control embeded videos

Slides WE1AA05 [3.764 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2022-WE1AA05

About •

Received ※ 14 August 2022 — Revised ※ 21 August 2022 — Accepted ※ 01 September 2022 — Issue date ※ 16 September 2022

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPOJO01

The ARES Linac at DESY

experiment, electron, linac, diagnostics

691

F. Burkart, R.W. Aßmann, H. Dinter, S. Jaster-Merz, W. Kuropka, F. Mayet, T. Vinatier
DESY, Hamburg, Germany

The generation and acceleration of ultra-short, high quality electron beams has attracted more and more interest in accelerator science. Electron bunches with these properties are necessary to operate and test novel diagnostics and advanced high gradient accelerating schemes. Furthermore, several medical and industrial applications require high-brightness electron beams. The dedicated R&D linac ARES at DESY (Deutsches Elektronen-Synchrotron) is now fully operational and able to produce these electron beams at the nominal energy of 155 MeV and deliver it to users. This paper gives an overview of the ARES linac and summarizes the beam parameter measurements. The possibilities for user operation will be described in detail.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2022-THPOJO01

About •

Received ※ 23 August 2022 — Revised ※ 31 August 2022 — Accepted ※ 01 September 2022 — Issue date ※ 06 September 2022

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)